|
|
|
Who's Online
There currently are 6043 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Perfect. Very good service and very good scanning quality. All sheets are very legible. Thank's
;
My first manual from Owner-Manuals.com but not the last! I am very satisfied with the easy ordering and promt delivery of a manual I did not find anywhere else.
 ;
This manual is very helpfull to use the Power Supply. All technical information has been available.
For service use the circuit diagrams are very good.
Thanks .
;
Very comprehensive document which is a must-have for any Satellit 2100 owner whose set up is somewhat intricate. Due to the bad quality of the pictures that are rather dark and a bit blurred I gave 4-star feedback.
;
The manual was missing 2 pages but when I presented the problem to the company they made every attempt to get the 2 pages to me, when they couldn't they refunded my money. A very pleasing and easy transaction. The manual they provided was the original, it was concise and to the point. I plan to do business with this company again when should the need arise.
POWER-HANDLING LIMITATIONS
The power-handling capability of any woofer is related to both its ability to dissipate heat and the maximum excursion limits of its cone. Once the speaker�s voice coil moves outside the magnetic gap, power can no longer be converted into motion and all the amplifier�s power is converted into heat in the voice coil. This voice-coil heating is the largest detriment to speaker longevity, so overexcursion should be avoided. Since speakercone excursion is different for each type of enclosure, power handling is different for each enclosure. Sealed enclosures exert the most control over the motion of a subwoofer because the air inside the box acts like a spring against the motion of the woofer cone. Larger boxes allow for more excursion, thus providing more low-frequency output for the amount of power used. When placed in a sealed box much larger than the Vas of the subwoofer, it will perform as if it were in an infinite-baffle installation. Vented and bandpass enclosures have the lowest amount of excursion for the amount of sound output. This is a result of port output reinforcing the sound output from the woofer. The mass of the air contained in the port provides an acoustic load on the woofer�s cone at the tuning frequency, and this added mass decreases woofer-cone excursion. Vented boxes do not provide adequate woofer control when driven below the tuned frequency (Fb), so proper design is important. A vented bandpass box will have the lowest overall cone excursion provided a subsonic filter is used. � Voice-coil overheating and burning due to overexcursion are often caused by overdriving an amplifier into �clipping. A severely clipped � signal, or square wave, contains nearly twice the power of a clean sine wave at the same level. Bass that sounds broken up and distorted at higher volumes is usually indicative of an amplifier that is clipping and being asked to deliver power beyond its ability. � Infinite-baffle or �free-air� mounting applications allow for greater cone excursion than subwoofers mounted in an enclosure. In order to compensate, the power handling of the subwoofer will likely be half its rated power in this application. � Study the excursion curves on the enclosed Reference Series data sheet and note the differences for different enclosure applications. The type and size of box used will produce different excursion demands on the enclosed subwoofer and, consequently, different levels of power handling. As long as the recommended enclosure parameters are used, the subwoofer will perform properly in its enclosed environment. However, any design deviation may result in less than optimum performance, and may also subject the subwoofer to overexcursion (i.e., where the voice coil leaves the gap) that can eventually damage the speaker. For additional help with this issue, please contact your authorized Infinity dealer.
SPECIFICATIONS
Reference 1020w Configuration: Nominal Impedance: Power Handling: Sensitivity @ 2.83V/1m: Frequency Response: Mounting Depth: Cutout Diameter: Reference 1220w Configuration: Nominal Impedance: Power Handling: Sensitivity @ 2.83V/1m: Frequency Response: Mounting Depth: Cutout Diameter: 10" subwoofer 4 ohms 250W RMS/1000W peak 90dB 22Hz � 800Hz 5-1/2" (140mm) 9-1/4" (235mm)
12" subwoofer 4 ohms 300W RMS/1200W peak 92dB 20Hz � 800Hz 6-1/8" (156mm) 11-1/8" (283mm)
-3-
|
|
|
> |
|
